Click image to enlarge
|
This hard shell Part # 300-010, mounts easily on all models of the EXO® Mask. It provides reinforced areas for mounting lights or small video cameras.
|
|
|
Click image to enlarge
|
To protect your EXO® Mask, the KMDSI mask carrying bag, Part # 300-902 should be used when transporting or storing your mask between dives. The KMDSI bag is made from extra heavy duty, black, ripstop nylon. The bottom of the bag is zippered for additional storage. The bag is also equipped with large carrying straps.
|
| Part # 305-036, |
|
|
The Air Inlet Swivel , Part # 305-036, is supplied on all Original EXO®s. It allows the regulator hose to move freely and align with the mask inlet without putting a stress on the hose coupling. It uses standard SCUBA threads for incoming breathing air. It may also be used on second stage scuba regulators and the EXO®-BR.
|
| Part # 325-635 |
Click image to enlarge
|
The Original EXO® mask has a nose pocket to allow SCUBA mask style ear equalizing. However, the use of some hoods with a thicker face seal, oversized gloves or 3 finger mitts can make pinching the nose difficult. Proper installation and use of this Nose Block Device Part # 325-635 will make equalizing very easy.
|
| Part # 325-090 |
Click image to enlarge
|
This kit, Part # 325-090, is for converting an Original EXO® 26 to the newer Oral Nasal configuration. Addition of the oral nasal can help keep CO2 levels to a minimum and improve communications.
Adding the oral nasal to the original EXO® Masks requires a change in the communications microphone mounting. Also, the automatic defogging up tube is removed, requiring the use of a commercial defogging solution.
|
|
|
| Part # 325-025 |
Click image to enlarge
|
This optional cushion, Part # 325-025, is designed to give divers with smaller faces a better seal in the EXO® Full Face mask. It is easily installed into the interior of the face seal. |
|
Part # 300-150, # 300-155. # 300-145
|
Click image to enlarge
|
The Manifold Block Assembly provides a control point for your bailout supply when using a light weight full face mask like the EXO® Mask®. It is equipped with four low pressure outlets and a check valve. It is available with a 9/16" O2 fitting or a #6 JIC fitting, or a standard scuba fitting.
9/16" O2 fitting, Part # 300-150
#6 JIC fitting, Part # 300-155
Standard scuba fitting, Part # 300-145
|
| Part # 200-017 |
Click image to enlarge
|
The KMDSI Overpressure Relief Valve is factory adjusted to vent any time the pressure in the low pressure hose connecting the bailout bottle to your emergency valve exceeds 200 P.S.I. It is installed in any of the low pressure ports in the first stage regulator.Overpressure Relief Valve, Part # 200-017
|
|
|
|
Click image to enlarge
|
Standard Hoods
|
Cold Water Hoods |
|
Small:
Part #: 310-030
|
Small:
Part #: 310-035 CW
|
|
Medium:
Part #: 310-031
|
Medium:
Part #: 310-037 CW
|
|
Large:
Part #: 310-032
|
Large:
Part #: 310-039 CW
|
|
|
|
Sizes
|
Small
|
Medium
|
Large
|
|
Around the Head
|
22 ½”
|
23 ½”
|
24 ½”
|
|
At Chin
|
21”
|
21 ½”
|
22”
|
|
At Neck
|
15”
|
16”
|
17”
|
|
The type of hood that a diver chooses may have direct bearing on the fit and comfort of the EXO®. Excess material on the chin and or jaw will keep the mask from positioning properly and possibly cause jaw fatigue. This may also prevent the diver's face from getting far enough into the mask for equalizing by pinching the nose.
When using a dry suit with a latex hood, no adjustment should be needed. However, if the hood covers too much of your face, it may be necessary to trim a small amount of rubber off the chin on the hood. If using a neoprene wet suit hood, you may want to trim material from the cheek bone downward to under the front part of the chin.
KMDSI manufacturers a hood perfectly tailored to the EXO® Full Face masks. It has thinner face seal material on the front as opposed to the thicker material of normal types of hoods, for better fit and comfort. Cold Water (CW) versions are also available. These have a large "bib" that tucks into the divers wet suit.
|
